5. Work Procedure and Technical Req

5.工作程序和技术要求<br>5.1。测试准备<br>5.工作程序和技术要求<br>5.1。测试准备<br>55.工作程序和技术要求<br>5.1。测试准备<br>5.2.2。断路器工作机理测试<br>检查储能电机：用万用表测量电机的绝缘电阻；用额定电压给电动机通电，检查电动机和储能电动机，确定它们是否可以正常工作。<br>真空断路器的五防功能检查：1.断路器处于合闸位置时，不能将断路器的手推车拉出；2.当断路器处于测试位置并处于接通状态时，应将锁定断路器的手推车推至工作位置；3.不能通过断路器手推车的移动来接通断路器；4.关于防止断路器跳闸，它只能以一个顺序接通一次；5.当断路器的手推车处于工作位置时，不能打开接地开关。6.当接地开关处于接通状态时，应将锁定断路器的手推车推至工作位置。<br>当断路器处于开合状态时，检查控制面板和指示灯是否正确显示；当接地开关处于打开/关闭状态时，检查控制面板并指示其应正确显示的位置。<br>检查断开和接通线圈的最小工作电压值。<br>5.2.3。测量绝缘电阻。<br>5.2.4。测量各相导电电路的直流电阻。

5. Work Procedure and Technical Requirements <br>5.1. Test preparation <br>5. Work Procedure and Technical Requirements<br>5.1. Test preparation<br>55. Work Procedure and Technical Requirements<br>5.1. Test preparation<br>5.2.2. Testing of Operating Mechanism of Circuit Breaker<br> Check of Energy-storage Motor: Use the megameter to measure the insulation resistance of the motor; electrify the motor with the rated voltage and check the motor and the energy-storage motor and ascertain whether they can operate normally or not.<br> Inspection of Five-prevention function of Vacuum Circuit Breaker: 1. When the circuit breaker is in the switch-on position, the handcart of the circuit breaker can’t be pulled out; 2. When the circuit breaker is in the testing position and switch-on state, the handcart of the locking circuit breaker should be pushed to the working position; 3. The circuit breaker can’t be switched on over the moving of the handcart of the circuit breaker; 4. As for the tripping prevention of the circuit breaker, it can be switched on for only once under one order; 5. The grounding switch can’t be turned on when the handcart of the circuit breaker is in the working position; 6. The handcart of the locking circuit breaker should be pushed to the working position when the grounding switch is on the switch-on state.<br> When the circuit breaker is on the opening/closing status, check the control panel and indicating lamp that they should display correctly; When the grounding switch is on the opening/closing status, check the control panel and indicating position that they should display right.<br> Check the minimum operation-voltage values of the switching-off and switching-on coils.<br>5.2.3. Measuring insulation resistance.<br>5.2.4. Measure the DC resistance of the conducting circuit of each phase.

5工作程序和技术要求<br>5.1条。试验准备<br>5工作程序和技术要求<br>5.1条。试验准备<br>55工作程序和技术要求<br>5.1条。试验准备<br>5.2.2条。断路器操动机构试验<br>检查储能电机：用兆欧表测量电机的绝缘电阻，用额定电压给电机通电，检查电机和储能电机是否能正常工作。<br>真空断路器五防功能检查：1。断路器在手拉位置时，断路器不能拔出。当断路器处于试验位置合闸状态时，应将闭锁断路器手车推到工作位置。断路器手车移动时不能合闸。对于断路器的防跳，一个命令下只能合闸一次。断路器手车处于工作位置时，接地开关不能合闸。当接地开关处于合闸状态时，应将闭锁断路器手车推到工作位置。<br>当断路器处于分、合闸状态时，应检查控制面板和指示灯是否正确显示；当接地开关处于分、合闸状态时，应检查控制面板和指示其正确显示的位置。<br>检查分合闸线圈的最小工作电压值。<br>5.2.3条。测量绝缘电阻。<br>5.2.4条。测量各相导电回路的直流电阻。